Long English Knock Out Punch Draw Stud 3/4"-16 Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

Step Down Draw Stud 3/4"-16 x 10mm Nut Included

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

THA100 Long English Knock Out Punch Draw Stud 3/4"-16 Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

TH0392-3/4" Conduit hole size Knockout punch unit with manual draw stud – (1.11" – Actual Hole Size)

TH0396-2" Conduit hole size Knockout punch unit with manual draw stud – (2.42" – Actual Hole Size)

2-1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

3 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

Step Drill Bit TH0357 - M35 Cobalt 3/16" - 15/16" for use with Electricians Conduit Knockout Punch

Designed Specifically for Electricians. Our long 3/16" steps properly drill holes sized for common draw studs on your conduit knock out punch set. No more going in through the other side or oversizing your hole just to get the draw stud in. Cuts Fast!...

3/4 inch Actual Hole Size Knockout Punch Unit with Manual Draw Stud (0.75 inch Actual Hole Size)

This punch units are complete units consisting of the .75 inch actual size punch and draw stud makes a 0.75 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver. Capacity: Mild steel plate through 10 gauge (3.5mm) Works to...

TH0391-1/2" Conduit hole size Knockout punch unit with manual draw stud – (0.86" – Actual Hole Size)

1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

Small English Knock Out Punch Draw Stud 3/8"-24 Thread + nut

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

TH0395-1 1/2" Conduit hole size Knockout punch unit & manual draw stud – (1.95" – Actual Hole Size)

4 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

Long Metric Knock Out Punch Draw Stud M20 x 1.5mm Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

Step Drill Bit TH0356 - M35 Cobalt 3/16" - 15/16" for use with Electricians Conduit Knockout with Titanium Nitride Coating

Designed Specifically for Electricians. Our long 3/16" steps properly drill holes sized for common draw studs on your conduit knock out punch set. No more going in through the other side or oversizing your hole just to get the draw stud in. Cuts Fast!...

TH0397 – Manual Knockout Punch Driver Kit for ½ inch to 1-1/4” inch Electrical Conduit Hole Sizes (1/2"- 1-1/4" Conduit size)

Manual drive knockout punches, for use with ratchet, wrench, or electric driver. Conduit punch sizes: 1/2",3/4",1",1-1/4 Capacity: Mild steel plate through 10 gauge (3.5mm) Works to punch Mild steel, Brass, Copper, Aluminum (soft alloys only),...

TEMCo THA114 3" Deep Draw Conduit Punch and Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 3" Required Punching Force: 13 US TonsActual Hole Size: 3.5"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16" Stainless Steel...

1 1/4 inch Actual Hole Size Knockout Punch Unit & Manual Draw Stud (1.25 inch Actual Hole Size)

This punch units are complete units consisting of the 1 1/4 inch actual size punch and draw stud makes a 1 1/4 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver. Capacity: Mild steel plate through 10 gauge (3.5mm) Works...

TEMCo THA112 2 inch Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 2" Required Punching Force: 9 US TonsActual Hole Size: 2.36"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16"...

TEMCo THA108 3/4" Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 3/4" Required Punching Force: 9 US TonsActual Hole Size: 1.05"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16"...

1 inch Actual Hole Size Knockout Punch Unit with Manual Draw Stud (1 inch Actual Hole Size)

This punch units are complete units consisting of the 1 inch actual size punch and draw stud makes a 1 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver. Capacity: Mild steel plate through 10 gauge (3.5mm) Works to...

TH0394-1 1/4" Conduit hole size Knockout punch unit & manual draw stud – (1.70" – Actual Hole Size)

Small Metric Knock Out Punch Draw Stud M10 x 1mm Thread + nut

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...