16 Standard Sizes in AWG
Conforms to DIN industrial terminal size standard. Compatible with all US domestic market terminals, including color coded lugs.
Applies even pressure on all sides creating sharp edges and high pullout resistance.
Proprietary half size dies accommodate hard-to-fit non-standard lug types.
Dies Imprint AWG Size
Imprints die size into crimped terminal for code compliance inspections.*
*Only on AWG sizes, not available in AWG+
How to Use:
Install the die set that matches your terminal size.
Close the release valve by rotating to the right (clockwise).
Pump the handle until the resistance felt becomes significant or the dies bottom out.
Open the release valve by rotating to the left (counter-clockwise). Your termination is now complete.
TEMCo TRUE-HEX Crimp Forming Dies apply uniform pressure on all sides for even compression.
Leading competitors flattened hex profile attempts to compensate for poor die to terminal fit. This under crimps and often leaves sharp “wings.”
TEMCo dies are sized to USA market industrial standards.
Leading competitor dies utilize an estimated metric conversion, leading to incorrect sizing.
TEMCo Dies imprint the AWG on your terminal for inspector proof of correct application.
Leading competitor dies will imprint either the non-standardized metric size or often nothing at all.
32 Die Sets
Included half sizes (indicated by +) allow for fine adjustments to the size of your crimp.
Dies imprint the size into the crimped terminal for code compliance inspections.
16 Standard size dies conform to DIN industrial standards and are compatible with all US domestic market terminals, including color coded lugs.
10, 8, 6, 4, 2, 1, 1/0, 2/0, 3/0, 4/0, 250 MCM, 300 MCM, 350 MCM, 400 MCM, 500 MCM, 600 MCMHALF SIZES:
10+, 8+, 6+, 4+, 2+, 1+, 1/0+, 2/0+, 3/0+, 4/0+, 250 MCM+, 300 MCM+, 350 MCM+, 400 MCM+, 500 MCM+, 600 MCM+
- Crimping Type::
- Crimping Force:
- 11 US Tons
- Crimping Action:
- Stroke Length:
- 0.8661 (22 mm)
- Terminal Type:
TH0005 V2.0 Hydraulic Cable Crimper
The TH0005 V2.0 Hydraulic cable lug crimper is a well built tool that comes with a 32 die set. Well made and is heavy duty that will last for years to come. Good company customer service that you can depend on.
Solid as Steel!!
You get what you pay for. You pay for these and you get one heavy duty crimper! Excellent quality, and excellent tool. The ergonomics are great, extra set of seals just incase, two sets of each die (4 not 2 of each die) and solid construction.
Hydraulic Crumpler TH0005
I purchased this crimper to create heavy duty battery cables for my trawler and heavy AC power cables for the generator supply lines to the distribution panel. The unit worked very well, and was easy to use. Having the slightly larger “+” sizes dies came in handy with the Anchor brand marine lugs. They are a bit thicker than the normal lugs and with the normal size die they are a bit over crimped. Clearly the company knows this and supplies the slightly larger dies to get the job done perfectly. This is the attention to detail I am looking for in a tool. If I am going to do the job, I want it done right. Especially in the case of the electrical supply lines in a boat my family travels on. High quality product that includes about any crimp die you could ever want/need. There will be no buyer’s remorse with the purchase of this unit.
Th0005 lug crimper
I have to say right out the box the product is beyond my expectations it’s a solid tool and gives solid crimps it’s really just like you have just solder the connection instead of crimping it. Thank you again for another good product.
Solid tool! Excellent crimps!
Overall great tool. I had problems at first getting the crimper to reach terminal pressure. The resistance while pumping would increase, but I could keep pumping even after dies had closed. I contacted customer service who suggested I try using a pair of pliers to tighten the close valve an extra quarter turn and that did the trick. After that it worked fine with just hand tightening. Only thing I'm a little confused by is that they send an extra set of seals, but the manual has no instructions on how to replace and says tool should only be serviced by certified Tempco technician.
This hydraulic cable lug crimper worked perfectly. I used the recommended die for my wire/terminal, and it makes perfect crimps every time. Very easy to use.
I looked at several crimpers before selecting this one. Upon opening the case it was obvious the quality exceeded my expectation. This is truly an example of you get what you pay for. The customer service was superior and it delivered as promised. I will purchase from TEMCo in the future and highly suggest you do the same.
Price,quality is great. Need USPS or UPS 6 day delivery service,for low cost.
Nice crimper - missing 3/0 dia
Knew I had a motor home battery re wire job coming up. Ordered this crimper ahead of time to be ready. Started this morning - a few 3/0 crimps are required - there is NO 3/0 dia included. Not sure if there is a work around or not. Kind of disappointed. Otherwise quality test crimps were made using 1/0 dia and braided lightning grounding cable. Still may order a few of these for my work as they do make a great crimp with the correct size dia.
Quality piece of equipment for a very good price and free shipping too.
Worked as advertised for crimping large gauge lugs. This is a quality piece of equipment that is well built and not junk. Great web site showing what the crimp should look like.