4 inch Hydraulic Knockout Punch - Electrical Conduit Hole Cutter Tool Set

The TEMCo TH0037 Hydraulic Knockout Punch has a powerful 13 US TRUE TON punching capacity and produces perfect, uniform holes every time. Its compact design is especially designed for field use on construction sites and maintenance jobs. Quick,...

2 inch Hydraulic Knockout Punch - Electrical Conduit Hole Cutter Tool Set

The TEMCo TH0004 Hydraulic Knockout Punch has a powerful 9 US TRUE TON punching capacity and produces perfect, uniform holes every time. Its compact design is especially designed for field use on construction sites and maintenance jobs. Quick, effortless...

Long English Knock Out Punch Draw Stud 3/4"-16 Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

Step Down Draw Stud 3/4"-16 x 10mm Nut Included

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

THA100 Long English Knock Out Punch Draw Stud 3/4"-16 Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

TH0390 – Manual Knockout Punch Driver Kit for ½ inch to 2 inch Electrical Conduit Hole Sizes (1/2"-2" Conduit Size)

Manual drive knockout punches, for use with ratchet, wrench, or electric driver. Conduit punch sizes: 1/2",3/4",1",1-1/4, 1-1/2", 2" Capacity: Mild steel plate through 10 gauge (3.5mm) Works to punch Mild steel, Brass, Copper, Aluminum (soft alloys...

TH0392-3/4" Conduit hole size Knockout punch unit with manual draw stud – (1.11" – Actual Hole Size)

TEMCo Hydraulic Knockout Punch Driver Electrical Conduit Hole KO Tool 3/4"-16

Hydraulic unit provides true 13 US ton hydraulic punching force. Compatible with GREENLEE and other domestic punch tooling, draw studs or arbors that use 3/4-16 thread size Hydraulic unit is the same unit used for TEMCo TH0037 Knockout Punch. ⚠️...

TH0396-2" Conduit hole size Knockout punch unit with manual draw stud – (2.42" – Actual Hole Size)

   ⚠️ This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

SQUARE 45MM X 45MM (1/16 DIN) PANEL METER PUNCH DIES 1.772 inch X 1.772 inch

This punch set is designed for punching holes in panels for common fractional DIN sized meters, gauges and process controllers. The unique design uses an indexed mandrell for male-to-female die rotational alignment ensuring high quality punching...

Manual Lever Sheet Metal Stud Punch

Compound Lever Linkage reduces effort applied by up to 50%. Hardened Tool Steel Punch Dies are guaranteed to outlast generic models. Punches more than 10 times faster than wrench types. Compact, light weight design for field use on construction sites and...

TH0307 Square 92mm x 92mm 1/4 DIN Panel Meter Punch Dies 3.622" x 3.622"

Square DIN Punch Die Set for 92mm x 92 mm (1/4 DIN) Fits TEMCo Industrial, Greenlee and other English punch sets (3/4-16") OR Fits other import metric punch sets (20 x 1.5mm). Draw studs and spacers are included for all of the above specifications. ...

Rectangle 92mm x 46mm 1/8 DIN Panel Meter Punch Dies 3.622 inch x 1.811 inch

This punch set is designed for punching holes in panels for common fractional DIN sized meters, gauges and process controllers. The unique design uses an indexed mandrell for male-to-female die rotational alignment ensuring high quality punching...

2-1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

3 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

3/4 inch Actual Hole Size Knockout Punch Unit with Manual Draw Stud (0.75 inch Actual Hole Size)

This punch units are complete units consisting of the .75 inch actual size punch and draw stud makes a 0.75 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver. Capacity: Mild steel plate through 10 gauge (3.5mm) Works to...

Step Drill Bit TH0357 - M35 Cobalt 3/16" - 15/16" for use with Electricians Conduit Knockout Punch

Designed Specifically for Electricians. Our long 3/16" steps properly drill holes sized for common draw studs on your conduit knock out punch set. No more going in through the other side or oversizing your hole just to get the draw stud in. Cuts Fast!...

Rectangle 22.5mm x 45mm (1/32 DIN) Panel Meter Punch Dies 0.886 inch x 1.772 inch

This punch set is designed for punching holes in panels for common fractional DIN sized meters, gauges and process controllers. The unique design uses an indexed mandrel for male-to-female die rotational alignment ensuring high quality punching...

TH0391-1/2" Conduit hole size Knockout punch unit with manual draw stud – (0.86" – Actual Hole Size)

  ⚠️ This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.

Punch & Die Set, Non-Conduit 5/8 3/4 7/8 1 1.125 1.25 1.375 1.50 1.625 1.75 1.875 2.00

Our punch dies are sized to non-conduit sizes, in other words, actual/measured hole sizes. In other words, a 1/2" punch and die produced a measured hole size of 1/2".This distinction is important as the common application of a punch and die is when an...

Dimple Die Set Tool Kit 8pcs: 1/2 inch 3/4 inch 1 inch 1-1/4 inch 1-1/2 inch 1-3/4 inch 2 inch 2-1/2 inch

This dimple die set works with a hydraulic driver and cylinder tool most commonly used with hydraulic knockout sets like our TEMCo THA043 and TH0372. This allows the user to easily work on larger work pieces without the hassle of wrestling it under a...

1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

Small English Knock Out Punch Draw Stud 3/8"-24 Thread + nut

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

TH0395-1 1/2" Conduit hole size Knockout punch unit & manual draw stud – (1.95" – Actual Hole Size)

   ⚠️ This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov.