Step Drill Bit TH0356 - M35 Cobalt 3/16" - 15/16" for use with Electricians Conduit Knockout with Titanium Nitride Coating

Designed Specifically for Electricians. Our long 3/16" steps properly drill holes sized for common draw studs on your conduit knock out punch set. No more going in through the other side or oversizing your hole just to get the draw stud in. Cuts Fast!...

4 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

TH0397 – Manual Knockout Punch Driver Kit for ½ inch to 1-1/4” inch Electrical Conduit Hole Sizes (1/2"- 1-1/4" Conduit size)

Manual drive knockout punches, for use with ratchet, wrench, or electric driver. Conduit punch sizes: 1/2",3/4",1",1-1/4 Capacity: Mild steel plate through 10 gauge (3.5mm) Works to punch Mild steel, Brass, Copper, Aluminum (soft alloys only),...

Double D Punch Die Set 0.769 inch x 0.642 inch Knockout Hole w/ Case

This punch set is designed for punching holes in panels for various cam locks, outlet receptacles, and conduits on sheet metal, fiberglass, plastic, and more. The unique design uses an indexed mandrell for male-to-female die rotational alignment...

TEMCo THA114 3" Deep Draw Conduit Punch and Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 3" Required Punching Force: 13 US TonsActual Hole Size: 3.5"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16" Stainless Steel...

Long Metric Knock Out Punch Draw Stud M20 x 1.5mm Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

1 1/4 inch Actual Hole Size Knockout Punch Unit & Manual Draw Stud (1.25 inch Actual Hole Size)

This punch units are complete units consisting of the 1 1/4 inch actual size punch and draw stud makes a 1 1/4 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver. Capacity: Mild steel plate through 10 gauge (3.5mm) Works...

TEMCo THA116 4" Deep Draw Conduit Punch and Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 4" Required Punching Force: 13 US TonsActual Hole Size: 4.5"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16" Stainless Steel...

TH0388 Dimple Die Set Tool Kit 6pcs for Conduit Knockout Sizes: (1/2") 0.86", (3/4") 1.05", (1”) 1.33", (1-1/4") 1.69", (1-1/2") 1.93", (2") 2.36"

Double D Punch Die Set 1-3/8 inch x 1-1/8 inch Knockout Hole w/ Case

This punch set is designed for punching holes in panels for various cam locks, outlet receptacles, and conduits on sheet metal, fiberglass, plastic, and more. The unique design uses an indexed mandrell for male-to-female die rotational alignment...

TH0394-1 1/4" Conduit hole size Knockout punch unit & manual draw stud – (1.70" – Actual Hole Size)

TEMCo THA112 2 inch Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 2" Required Punching Force: 9 US TonsActual Hole Size: 2.36"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16"...

2-1/2 inch, 3 inch, 3-1/2 inch, 4 inch Conduit Punch and Die Set for Knockout

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

Small Metric Knock Out Punch Draw Stud M10 x 1mm Thread + nut

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

TEMCo THA108 3/4" Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 3/4" Required Punching Force: 9 US TonsActual Hole Size: 1.05"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16"...

1 inch Actual Hole Size Knockout Punch Unit with Manual Draw Stud (1 inch Actual Hole Size)

This punch units are complete units consisting of the 1 inch actual size punch and draw stud makes a 1 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver. Capacity: Mild steel plate through 10 gauge (3.5mm) Works to...

3/4 inch Conduit Punch and Die For Hydraulic Knock Out Driver

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

1 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

TEMCo THA113 2-1/2" Deep Draw Conduit Punch - Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 2-1/2" Required Punching Force: 13 US TonsActual Hole Size: 3"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16" Stainless Steel...

TEMCO THA107 1/2" Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 1/2" Required Punching Force: 9 US TonsActual Hole Size: 0.86"Fits Draw Stud Size: TEMCo THA012, THA013, THA015 or any draw stud with a diameter of 0.430" (10.90mm)  Punching...

3-1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means, for example, a 1" punch die will correctly punch for a...

TEMCo THA109 1" Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 1" Required Punching Force: 9 US TonsActual Hole Size: 1.33"Fits Draw Stud Size: 3/4" -16 (TEMCo THA0001 and THA100 draw studs)  Punching Thickness Capacity: 1/8" (11 ga) Steel, 1/16"...

Short Metric Knock Out Punch Draw Stud M20 x 1.5mm Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and any other critical specifications are the ones you'll...

TH0393-1" Conduit hole size Knockout punch unit with manual draw stud – (1.36" – Actual Hole Size)