TEMCo THA114 3" Deep Draw Conduit Punch and Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 3" Required Punching Force: 13 US TonsActual Hole Size: 3.5"<

Small English Knock Out Punch Draw Stud 3/8"-24 Thread + nut

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

TH0395-1 1/2" Conduit hole size Knockout punch unit & manual draw stud – (1.95" – Actual Hole Size)

Long Metric Knock Out Punch Draw Stud M20 x 1.5mm Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

1 1/4 inch Actual Hole Size Knockout Punch Unit & Manual Draw Stud (1.25 inch Actual Hole Size)

This punch units are complete units consisting of the 1 1/4 inch actual size punch and draw stud makes a 1 1/4 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver...

TH0397 – Manual Knockout Punch Driver Kit for ½ inch to 1-1/4” inch Electrical Conduit Hole Sizes (1/2"- 1-1/4" Conduit size)

Manual drive knockout punches, for use with ratchet, wrench, or electric driver. Conduit punch sizes: 1/2",3/4",1",1-1/4 Capacity: Mild steel plate through 10 gauge (3.5mm) Works to punch Mild...

Double D Punch Die Set 1-3/8 inch x 1-1/8 inch Knockout Hole w/ Case

This punch set is designed for punching holes in panels for various cam locks, outlet receptacles, and conduits on sheet metal, fiberglass, plastic, and more. The unique design uses an indexed...

Step Drill Bit TH0356 - M35 Cobalt 3/16" - 15/16" for use with Electricians Conduit Knockout with Titanium Nitride Coating

Designed Specifically for Electricians. Our long 3/16" steps properly drill holes sized for common draw studs on your conduit knock out punch set. No more going in through the other side or...

TEMCo THA108 3/4" Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 3/4" Required Punching Force: 9 US TonsActual Hole Si

TEMCo THA116 4" Deep Draw Conduit Punch and Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 4" Required Punching Force: 13 US TonsActual Hole Size: 4.5"<

TEMCo THA112 2 inch Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 2" Required Punching Force: 9 US TonsActual Hole Size

1 inch Actual Hole Size Knockout Punch Unit with Manual Draw Stud (1 inch Actual Hole Size)

This punch units are complete units consisting of the 1 inch actual size punch and draw stud makes a 1 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver. Capacity:...

TH0388 Dimple Die Set Tool Kit 6pcs for Conduit Knockout Sizes: (1/2") 0.86", (3/4") 1.05", (1”) 1.33", (1-1/4") 1.69", (1-1/2") 1.93", (2") 2.36"

This set is designed for use with conduit size punch and dies that produce electrical conduit size holes. Recommended set is our TH0004 KO set.   

2-1/2 inch, 3 inch, 3-1/2 inch, 4 inch Conduit Punch and Die Set for Knockout

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

Small Metric Knock Out Punch Draw Stud M10 x 1mm Thread + nut

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

TH0394-1 1/4" Conduit hole size Knockout punch unit & manual draw stud – (1.70" – Actual Hole Size)

TEMCO THA107 1/2" Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 1/2" Required Punching Force: 9 US TonsActual Hole Si

TEMCo Hydraulic Knockout Punch Driver Only 9 US Ton 3/4"-16 Thread

TEMCo ID: SP0036

3/4 inch Conduit Punch and Die For Hydraulic Knock Out Driver

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

1 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

TEMCo THA113 2-1/2" Deep Draw Conduit Punch - Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 2-1/2" Required Punching Force: 13 US TonsActual Hole Size: 2.908"

TEMCo THA109 1" Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 1" Required Punching Force: 9 US TonsActual Hole Size

TEMCo THA002 Conversion Draw Stud found in TH0360 and TH0372 KO Sets

Replacement THA002 draw stud that is found in the TH0360 and TH0372 KO sets Thread is M20x1.5 to 3/4"-16 with an internal thread of 3/8"-24 Length is 5-13/16"

3-1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...