TH0393-1" Conduit hole size Knockout punch unit with manual draw stud – (1.36" – Actual Hole Size)

English Draw Stud 3/4-16" Thread for TEMCo TH0304 Punch Set

  Direct replacement English draw stud for TEMCo TH0304 punch Length is 5.19 in Thread of the draw stud is 3/4-16" Does not include the k

TEMCo THA014 Long English Draw Stud found in TH0370 and TH0388 Dimple Die Sets

Replacement THA014 draw stud that is found in the TH0370 and TH0388 Dimple Die sets Thread is 3/4"-16 with an internal thread of 3/8"-24 Length is 6-1/16" ⚠️ This product can expose you to...

2 inch Conduit Punch and Die For Hydraulic Knock Out Driver M20x1.5mm Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

Short Metric Knock Out Punch Draw Stud M20 x 1.5mm Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

2-1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver M20x1.5mm Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

3 inch Conduit Punch and Die For Hydraulic Knock Out Driver M20x1.5mm Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

THA028 2 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

TEMCo TH0368 Dimple Die for 2-1/2” Actual Hole Size

This dimple die set creates flared holes. Cut out holes inherently provide reduced weight of the work piece, and these dimple dies create rigidity by flaring the holes. ⚠️ This product can expose you...

TEMCo TH0363 Dimple Die for 1” Actual Hole Size

This dimple die set creates flared holes. Cut out holes inherently provide reduced weight of the work piece, and these dimple dies create rigidity by flaring the holes. ⚠️ This product can expose you...

TEMCo TH0362 Dimple Die for 3/4” Actual Hole Size

This dimple die set creates flared holes. Cut out holes inherently provide reduced weight of the work piece, and these dimple dies create rigidity by flaring the holes. ⚠️ This product can expose you...

TEMCo TH0361 Dimple Die for 1/2” Actual Hole Size

This dimple die set creates flared holes. Cut out holes inherently provide reduced weight of the work piece, and these dimple dies create rigidity by flaring the holes. ⚠️ This product can expose you...

TEMCo THA115 3-1/2" Deep Draw Conduit Punch - Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 3-1/2" Required Punching Force: 13 US TonsActual Hole Size: 3.93"

1-1/4 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

TEMCo TH0365 Dimple Die for 1-1/2” Actual Hole Size…

This dimple die set creates flared holes. Cut out holes inherently provide reduced weight of the work piece, and these dimple dies create rigidity by flaring the holes. ⚠️ This product can expose you...

TEMCo THA111 1-1/2" Slug Splitting Conduit Punch/Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 1-1/2" Required Punching Force: 9 US TonsActual Hole

1-1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

TEMCo THA021 English Thread Draw Stud for TH0358 Punch Set

Replacement English THA021 draw stud that is found in the TH0358 Punch set Thread is 3/4"-16 to 3/8"-24 Length is 5-1/16" Does not include the knurrled nut ⚠️ This product can e

TEMCo THA110 1-1/4" Slug Splitting Conduit Punch/Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 1-1/4" Required Punching Force: 9 US TonsActual Hole

TH0387 Dimple Die for 2” Conduit Hole Size – 2.36” Actual Hole Size

Dimple Die for 2” Conduit Hole Size – 2.36” Actual Hole Size Rated For 3/16" Mild Steel. Recommended Minimum Forming Tonnage: 13. This dimple die set creates flared holes. Cut out holes...

TEMCo TH0386 Dimple Die for 1-1/2” Conduit Hole Size – 1.93” Actual Hole Size

Dimple Die for 1-1/2” Conduit Hole Size – 1.93” Actual Hole Size Rated For 3/16" Mild Steel. Recommended Minimum Forming Tonnage: 13. This dimple die set creates flared holes. Cut out holes...

TH0382 Dimple Die for 1/2” Conduit Hole Size - 0.86” Actual Hole Size

Dimple Die for 1/2” Conduit Hole Size - 0.86” Actual Hole Size Rated For 3/16" Mild Steel. Recommended Minimum Forming Tonnage: 13. This dimple die set creates flared holes. Cut out holes...

1 inch Conduit Punch and Die For Hydraulic Knock Out Driver M20x1.5mm Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

TEMCo THA045 Draw Stud with Bearing for TH0390 or TH0397 Set

Replacement THA045 draw stud with bearing that is found in the TH0390 or TH0397 Knock out sets Draw Stud with 19mm Hex on one side, The other side has Standard 3/4"-16 threads. Length is 3.8"