Long English Knock Out Punch Draw Stud 3/4"-16 Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

THA100 Long English Knock Out Punch Draw Stud 3/4"-16 Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

Step Down Draw Stud 3/4"-16 x 10mm Nut Included

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

TH0392-3/4" Conduit hole size Knockout punch unit with manual draw stud – (1.11" – Actual Hole Size)

TH0396-2" Conduit hole size Knockout punch unit with manual draw stud – (2.42" – Actual Hole Size)

TH0391-1/2" Conduit hole size Knockout punch unit with manual draw stud – (0.86" – Actual Hole Size)

  ⚠️ This product can expose you to chemicals

3/4 inch Actual Hole Size Knockout Punch Unit with Manual Draw Stud (0.75 inch Actual Hole Size)

This punch units are complete units consisting of the .75 inch actual size punch and draw stud makes a 0.75 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver...

3 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

Step Drill Bit TH0357 - M35 Cobalt 3/16" - 15/16" for use with Electricians Conduit Knockout Punch

Designed Specifically for Electricians. Our long 3/16" steps properly drill holes sized for common draw studs on your conduit knock out punch set. No more going in through the other side or...

2-1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

1/2 inch Conduit Punch and Die For Hydraulic Knock Out Driver

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

4 inch Conduit Punch and Die For Hydraulic Knock Out Driver 3/4 inch-16 Thread

Our punch dies are sized to conduit sizes, not actual hole sizes. Electricians use these sizes because conduits are measured by the inner diameter of the tube, not their outer diameter. That means,...

TEMCo THA114 3" Deep Draw Conduit Punch and Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 3" Required Punching Force: 13 US TonsActual Hole Size: 3.5"<

Small English Knock Out Punch Draw Stud 3/8"-24 Thread + nut

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

TH0395-1 1/2" Conduit hole size Knockout punch unit & manual draw stud – (1.95" – Actual Hole Size)

1 1/4 inch Actual Hole Size Knockout Punch Unit & Manual Draw Stud (1.25 inch Actual Hole Size)

This punch units are complete units consisting of the 1 1/4 inch actual size punch and draw stud makes a 1 1/4 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver...

Long Metric Knock Out Punch Draw Stud M20 x 1.5mm Thread

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...

TEMCo THA108 3/4" Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 3/4" Required Punching Force: 9 US TonsActual Hole Si

TH0397 – Manual Knockout Punch Driver Kit for ½ inch to 1-1/4” inch Electrical Conduit Hole Sizes (1/2"- 1-1/4" Conduit size)

Manual drive knockout punches, for use with ratchet, wrench, or electric driver. Conduit punch sizes: 1/2",3/4",1",1-1/4 Capacity: Mild steel plate through 10 gauge (3.5mm) Works to punch Mild...

Step Drill Bit TH0356 - M35 Cobalt 3/16" - 15/16" for use with Electricians Conduit Knockout with Titanium Nitride Coating

Designed Specifically for Electricians. Our long 3/16" steps properly drill holes sized for common draw studs on your conduit knock out punch set. No more going in through the other side or...

1 inch Actual Hole Size Knockout Punch Unit with Manual Draw Stud (1 inch Actual Hole Size)

This punch units are complete units consisting of the 1 inch actual size punch and draw stud makes a 1 inch sized hole. Knockout punch can be used with ratchet, wrench, or electric driver. Capacity:...

TEMCo THA116 4" Deep Draw Conduit Punch and Die for Hydraulic Knock Out Driver

Deep Draw Conduit Punch for Fitting Size: 4" Required Punching Force: 13 US TonsActual Hole Size: 4.5"<

TEMCo THA112 2 inch Slug Splitting Conduit Punch - Die for Hydraulic Knock Out Driver

Slug Splitting Conduit Punch for Fitting Size: 2" Required Punching Force: 9 US TonsActual Hole Size

Small Metric Knock Out Punch Draw Stud M10 x 1mm Thread + nut

This draw stud is used for our TH0004 and TH0037 hydraulic knock out punches, but can also be used for any other knockout punch set you might be using. Just make sure the thread sizes, length, and...